An element of the working body (brush) of the aerodrome sweeper – a synchronous hydromechanical drive – is considered. It is based on the throttle flow divider of the non-spool type plunger setters, and it is driven by two hydraulic motors. Its mathematical model is offered. Special attention is given to describing the stress state of the brush shaft when twisting under the variable load, and to identifying the effect of the shaft elastic properties on the dynamic properties of the synchronous hydromechanical system. In this paper, modeling of the synchro-nous hydromechanical brush drive system, unlike the conventional method, is based on the use of the reduced volume stiffness of the hydraulic system. This simplifies the modeling and allows performing a rapid analysis of the test drive operation which significantly reduces the design time of the drive system with the given perfor-mance properties.
volume stiffness of the hydraulic actuator, mathematical model, mobile technology machine, hydraulic drive, throttle synchronization, twisting shaft of working body
Введение. Многие, в том числе и мобильные, технологические машины содержат синхронные гидромеханические приводы, в которых необходимо обеспечить работу двух или более гидравлических двигателей, запитываемых от одного источника расхода – насоса, гидроаккумулятора и др. Как показали ранее проведенные исследования, решение подобных задач проще всего осуществлять с использованием дроссельных делителей потока [1, 2, 3].
Настоящая работа посвящена исследованиям синхронного гидромеханического привода мобильной технологической машины на примере привода щётки аэродромной уборочной машины на базе дроссельного делителя потока не золотникового типа.
1. Rybak, A. T. Teorija i metodologija raschjota i proektirovanija sistem privodov tehnologicheskih mashin i agregatov APK: avtoref. dis. … doktora tehn. nauk. [Theory and methodology of calculation and de-sign of drive systems of agribusiness technology machines and units: Dr. tech.sci.diss., author’s abstract.] Ros-tov-on-Don, 2011, 39 p. (in Russian).
2. Rybak, A. T. Modelirovanie i raschjot gidromehanicheskih sistem na stadii proektirovanija: mono-grafija. [Simulation and calculation of hydromechanical systems at the design stage: monograph.] Rostov-on-Don : DSTU Publ. Centre, 2006, 167 p. (in Russian).
3. Antonenko, V. I., Sidorenko, V. S. Ne prjamoe regulirovanie v mnogodvigatel´nyh gidromehanich-eskih sistemah. [Indirect regulation in multiengine hydrosystems.] Vestnik of DSTU, 2010, vol. 10, no. 1 (44), pp. 70 - 75 (in Russian).
4. Zharov, V. P., Rybak, A. T., Korchagin, A. V. Dinamicheskaja model´ gidromehanicheskoj sistemy ajerodromnoj uborochnoj mashiny. [Dynamic model of hydromechanical system of aerodrome sweeper.] Izv. Vuzov. Sev.-Kavk. Region. Tehn. nauki. 2006, no. 2, pp. 68 - 73 (in Russian).
5. Rybak, A. T., Martynenko, A. I., Ustyantsev, M. V. Sistema privoda shhjotki ajerodromnoj ub-orochnoj mashiny s drossel´noj sinhronizaciej raboty gidromotorov. [Brush drive system of aerodrome sweeper with hydromotor throttle synchronization .] Vestnik of DSTU, 2011, vol. 11, no. 4 (55), pp. 505-512 (in Rus-sian).
6. Temirkanov, A. R., Rybak, A. T. Sinhronnyj gidromehanicheskij privod rabochego organa mobil´noj mashiny i ego matematicheskaja model´. [Synchronous hydromechanical drive of the mobile machine actuator and its mathematical model.] Vestnik of DSTU, 2013, no. 3-4 (72-73), pp. 104-110 (in Russian).
7. Feodosyev, V. I. Soprotivlenie materialov: Uchebnik dlja vtuzov - 9-e izd., pererab. [Strength of materials: a textbook for higher technical schools. 9th rev. ed.] Moscow : Gl. red. fiz.-mat. liter., 1986, 512 p. (in Russian).
8. Sidorenko, V. S., Le Chung Kien. Modelirovanie dinamicheskoj sistemy linejnogo pozicionirovanija gidroprivoda podachi agregatnoj sverlil´noj golovki stanka. [Simulation of linear position hydraulic drive for ma-chine power drill feed.] Vestnik of DSTU, 2013, no. 5-6 (74-75), pp. 153-159 (in Russian).
9. Rybak, A. T., Boguslavskiy, I. V. Sovershenstvovanie metodiki raschjota sistem privodov tehnolog-icheskogo oborudovanija. [Improving the method for calculating drive systems of processing equipment.] Vest-nik mashinostroenija, 2010, no. 10, pp. 39-46 (in Russian).
10. Boguslavskiy, I. V., Rybak, A. T., Chernavskiy, V. A. Nauchno-metodologicheskie osnovy proek-tirovanija privodov tehnologicheskih mashin. [Scientific and methodological bases for designing technological machine drives.] Rostov-on-Don : GOU DPO IUI AP, 2010, 276 p. (in Russian).
